Wireless Keypad (OKP-BX) with CodeDodger®2019-01-14T19:13:48+00:00

 

Programming Wireless Keypad (OKP-BX) with CodeDodger®

Download PDF instructions of CodeDodger®: English    Spanish    French

Wireless Keypad (OKP-BX) with CodeDodger®

NOTE: For Convenience – Program Keypad BEFORE mounting.

Program Keypad for One Garage Door (Code Dodger 2)

Create Your Wireless Keypad PIN (Personal Identification Number)

On your wireless keypad:

  • Press in order 3, 5, 7
  • Press the PROGRAM key
  • Enter your PIN (3 to 8 characters)
  • Press the PROGRAM key again.
  • Close keypad cover and wait 30 seconds

Program the keypad for a single door

On the power head:

  • Press and hold the PROGRAM button until both LED lights turn BLUE
  • Release button. Only the round LED will remain BLUE.
  • Press and hold the PROGRAM button again then release. The Long LED will blink PURPLE
  • Enter your PIN number using the keys on the keypad
  • Press the UP/DOWN button. LEDs will stay on solid.
  • Press the UP/DOWN button again. LEDs will turn off.
  • Press any key to stop opener. (It will automatically stop at the fully open or fully closed position.)
  • The keypad backlight will turn off in approximately 30 seconds.

NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was

entered incorrectly. After the LED stops blinking, re-enter your PIN ad try again. Any keypad button will control the door for 30 seconds

after the door starts moving. Rapid blinking of the red LED indicates an error. After a few seconds, the LED will turn off. Start over.

Proceed to the Mounting Instructions

Program Keypad for Multiple Garage Doors (CodeDodger 2)

  • Create Your Wireless Keypad PIN (Personal Identification Number)
  • Press in order 3, 5, 7
  • Press the PROGRAM key
  • Enter your PIN (3 to 8 characters)
  • Press the PROGRAM key again.
  • Close keypad cover and wait 30 seconds
  • Program the keypad for multiple doors
  • All garage door openers will use the same PIN.

On the wireless keypad:

  • Enter your PIN and press the PROGRAM button.
  • Press the PROGRAM button again.
  • Press the number of doors you wish to control (2 or 3)

On your garage door opener power head:

  • Select first opener and press and hold the PROGRAM/SET button until both LED lights turn BLUE.
  • Release the button. Only the round LED will be BLUE.
  • Press the UP/DOWN button again. LEDs will turn off.
  • Press any key to stop opener. (It will automatically stop at the fully open or fully closed position.)
  • The keypad backlight will turn off in approximately 30 seconds.

NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the

LED stops blinking, re-enter your PIN and try again. Any keypad button will control the door for 30 seconds after the door starts moving.

Rapid blinking of the red LED indicates an error. After a few seconds, the LED will turn off. Start over.

Proceed to the Mounting Instructions

Mounting Instructions

The keypad must be mounted in sight of the door(s), at least 5 feet above the ground and clear of any moving door parts.

Mounting screws are located inside the battery compartment.

  • Remove battery cover and batteries
  • Drill a 1/16″ pilot hole for the tip mounting screw.
  • Install a screw into the drilled hole, leaving a 1/8″ gap between the screw head and the wall.
  • Hook the keypad over the screw.
  • Mark and drill pilot hole and fasten the bottom screw.
  • Install batteries and cover.

Additional Instructions

Change your PIN

  • Enter your current PIN and press the PROGRAM button
  • Enter your NEW PIN and press the PROGRAM button.

Using a Temporary PIN
A temporary PIN allows temporary access to your home by repair persons, meter readers, etc.

 Enter your current PIN and press the PROGRAM button 3 times.
  • Enter your temporary PIN and press the PROGRAM button.

NOTE: Do NOT reprogram the garage door opener(s). Temporary PIN remains active only until the next time your normal PIN is entered.

Forgot Your PIN (Resetting Wireless Keypad)

  • Press and hold the PROGRAM button
  • While holding the PROGRAM button, press and hold the UP/DOWN button for 5 seconds.
  • Release both buttons. You must now start from the beginning and reprogram you Wireless Keypad.

Changing Battery

  • If the keypad backlight does not come on, this indicates the need to replace the batteries.
  • Press in on the front of the battery cover and slide it down off of the keypad..
  • Remove used batteries and replace with “AAA” batteries.
  • No programming is lost during replacement of batteries.

Call us Today  +1 (858) 547-3600

Overhead Door Company of Southern California – 12215 Kirkham Road Suite 200, Poway, CA 92064


We are proud to serve the areas of Greater San Diego County and the following Cities:

San Diego County Cities:

Alpine, Bonita, Bonsall, Campo, Camp Pendelton, Cardiff-by-the-Sea, Carlsbad, Chula Vista, Coronado, Del Mar, Dulzura, and El Cajon. As well as Encinitas, Escondido, Fallbrook, Imperial Beach, Jacumba, Jamul, Julian, La Jolla La Mesa, Lakeside, Lemon Grove, MCAS Miramar. And also, Mira Mesa, Mt. Palomar, Poway, National City, Ocean Beach, Oceanside, Olivenhein, Pacific Beach, Pala, Pine Valley, Potrero, Rainbow. Ramona, Rancho Bernardo, Rancho Santa Fe, San Diego San Marcos, Santa Ysabel, Santee, San Ysidro, Solana Beach, Spring Valley Valley Center, Vista, and Warner Springs.

Riverside County Cities:

Temecula, Murrieta, Murrieta Hot Springs, Menifee Winchester, French Valley and also the surrounding Cities.